O-Ring Groove Dimensions for AS568-469

AS568-469 O-Ring Specifications

• Dash Number: AS568-469 (400 Series)
• Inside Diameter (ID): 9.35″ (237.49mm)
• Cross-Section (CS): 0.275″ (6.99mm) — 1/4″ nominal
• Outside Diameter (OD): 9.9″ (251.46mm)

Groove Dimensions for AS568-469

The groove dimensions below are based on Parker O-Ring Handbook recommendations for standard 1/4″ (6.99mm) cross-section o-rings. These provide the proper squeeze ratio for reliable sealing.

Face Seal (Static Application)

Face seals are the most common type — used when the o-ring sits in a groove on a flat surface with no relative motion between parts.

• Groove Depth: 0.21″ (5.33mm)
• Groove Width: 0.375″ (9.52mm)
• O-Ring Squeeze: 0.038″ to 0.065″ (13.8% to 23.6%)
• Gland Fill: ~75% maximum (allows for thermal expansion)

Piston Seal (Dynamic Application)

Piston seals sit in a groove on a piston that moves inside a bore. The o-ring seals against the bore wall.

• Groove Depth: 0.213″ (5.41mm)
• Groove Width: 0.375″ (9.52mm)
• O-Ring Squeeze: 0.035″ to 0.062″ (12.7% to 22.5%)
• Bore Diameter: O-ring OD (9.9″) + diametral clearance (typically 0.002″-0.005″)

Rod Seal (Dynamic Application)

Rod seals sit in a groove in a bore, sealing against a rod that passes through. The o-ring compresses radially against the rod.

• Groove Depth: 0.213″ (5.41mm)
• Groove Width: 0.375″ (9.52mm)
• O-Ring Squeeze: 0.035″ to 0.062″ (12.7% to 22.5%)
• Rod Diameter: O-ring ID (9.35″) minus diametral clearance

Why These Groove Dimensions?

O-ring groove design is a balance of three factors:

• Squeeze (compression): The groove must compress the o-ring enough to create a seal. For the AS568-469 (1/4″ CS), the target squeeze is 19% of the cross-section. Too little squeeze = leaks. Too much = excessive friction and premature wear.
• Gland fill: The o-ring should fill no more than ~75% of the groove volume. The remaining 25% is free space that allows for thermal expansion of the rubber compound.
• Width clearance: The groove width (0.375″) is wider than the o-ring cross-section (0.275″) to prevent pinching and allow the o-ring to move slightly under pressure.

Material Considerations

The groove dimensions above work for standard o-ring materials (Buna-N/Nitrile, Viton/FKM, EPDM, Silicone). For harder materials (90+ Shore A durometer), you may need to adjust squeeze slightly. Softer materials (below 60 Shore A) may require tighter grooves to prevent extrusion at high pressure.

Surface Finish Requirements

• Static seals: 32 microinch Ra (0.8 μm) maximum on sealing surfaces
• Dynamic seals: 16 microinch Ra (0.4 μm) maximum on sliding surfaces
• Groove bottom: 63 microinch Ra (1.6 μm) maximum
• Break all sharp edges — use 0.005″-0.015″ radius or 15° chamfer at groove corners

Related AS568 Sizes

• AS568-466 Groove Dimensions — ID: 8.6″ (1/4″ CS)
• AS568-467 Groove Dimensions — ID: 8.85″ (1/4″ CS)
• AS568-468 Groove Dimensions — ID: 9.1″ (1/4″ CS)
• AS568-470 Groove Dimensions — ID: 9.6″ (1/4″ CS)
• AS568-471 Groove Dimensions — ID: 9.85″ (1/4″ CS)
• AS568-472 Groove Dimensions — ID: 10.1″ (1/4″ CS)